• Companies
  • Contact
  • Français
  • Search icon
Logo Roctest
    • Products
    • Applications
    • Services
    • Case studies
    • Resources
    • About
      • About Us
      • News
      • Events
      • Careers
      • Contact
Close icon Close icon Logo Roctest
  • Search icon
    • Products
    • Applications
    • Services
    • Case studies
    • Resources
    • About
      • About Us
      • News
      • Events
      • Careers
      • Contact
  • Companies
  • Contact
  • Français
  • Logo linkedin
  • Logo youtube
Home » Case studies » CERN-LHC Dipoles

CERN-LHC Dipoles

Published on January 31 2017
  • Facebook Icon
  • Twitter Icon
  • LinkedIn Icon
  • Email Icon
Image CERN-LHC Dipoles

 

The LHC will consist of two colliding synchrotrons installed in the 27 km tunnel previously used by the LEP accelerator. They will be filled with protons and two superconducting magnetic channels will accelerate them. To bend 7 TeV protons around the ring, the LHC dipoles must be able to produce fields of 8.36 Tesla. Superconductivity makes this possible. The LHC machine will contain around 2000 main ring superconducting magnets cooled at 1.9 K by super-fluid pressurized helium. Figure 1 shows the concept of one of the 15 m-long LHC cryodipole. The magnet dipole, enclosed in the Helium Vessel with heat exchanger and cold bore tubes, forms the dipole cold-mass. The work temperature of the cold-mass is 1.9K. The cryostat of the dipole magnet consists of the three supports to position the cold mass, a radiation screen, a thermal shield both equipped with multi-layer super-insulation, and a vacuum vessel. The dipole cold-mass assembled into the cryostat forms the Cryodipole Magnet.

Aim of monitoring:

To ensure the correct functioning of the LHC, it is necessary to know the exact position of the cold mass in the vacuum vessel. This allows the correct positioning of the particle beam relative to the surveying points placed on the external face of the vacuum tube. During cooling and an increase of the magnetic field, the cold-mass changes its size, shape and position. The expected longitudinal deformation of the 15 m long cold-mass will be around 20 mm, caused mainly by thermal contraction. Determining the horizontal displacement of its extremities is much more important, but more difficult. This was the main goal of this project and in order to realize the measurements a new displacement sensor was developed. The extreme environmental conditions and the geometry have imposed several constraints during the design of the displacement sensors. Since the longitudinal displacement was significant (20 mm), it was not possible to install an optical fiber between the vacuum vessel and the cold mass. Therefore, it was decided to use a light beam propagating in the space between an optical head installed on the inner wall of the vacuum vessel and a mirror attached to the external surface of the cold mass. Optical fibers are used as a reference path in the optical head and to bring the light in and out of the vacuum tube. Functional principles and components of the displacement sensor are presented in Figure 2.

INSTALLATION PERIODTYPE OF SENSORSNUMBER OF SENSORS
2000SOFO30

Main results:

The first two measurement heads were installed in a test dipole in April 2000. The installation proceeded without problems and the optical alignment required less than 30 minutes. The sensors were installed at the dipole end as shown in Figure 3. A few days later the dipole was provided with end-caps and was displaced from the assembly hall to the testing hall. Measurements were registered during transportation and later, during the cool-down test. Figure 4 shows the recorded displacements during the cool-down test. It can be noted that the measured contraction of the dipole corresponded well to numerical simulation, while the displacement was much bigger than expected. The measurements are now regularly performed on each new LHC dipole with the addition of a third sensor installed below the dipole to measure vertical displacement.

Related Papers:

Development of a displacement sensor for the CERN-LHC superconducting Cryo-dipoles, D. Inaudi, B. Glisic, S. Fakra, W. Scandale, J. Garcia Perez, J. Billan , SPIE, 15th International Conference on Optical Fiber Sensors, Venice, Italy – (Vol 4185, p 29-32) – 2000
Displacement measurements in cryogenically cooled dipoles of the new CERN-LHC particle accelerator, D. Inaudi, B. Glisic, W. Scandale, J. Garcia-Perez, J. Billan, S. Rafaelli , SPIE, International symposium on Smart Structures and Materials, Newport Beach, USA – (Vol 4328, p 79-87) – 2001
Image

General view of one module of LHC

Image

Setup and picture of the sensor head

Image

Position of optical heads

Image

Related Applications

Nuclear Power Plant

Down arrow
close

Search Roctest

Searching...

Logo Roctest

Developer and Manufacturer of Geotechnical & Structural Instruments and Soil/Rock Testing Equipment

Logo Smartec

Provider of innovative Fiber Optic Solutions for Structural Health Monitoring and Geotechnical Instrumentation

Logo Telemac

Provider of Geotechnical & Structural Instruments
since 1947

Logo Enomfra

Provider of Hydrogeological & Geotechnical Services. Investigations, Monitoring & Testing

Logo Roctest

Developer and Manufacturer of Geotechnical & Structural Instruments and Soil/Rock Testing Equipment

Logo Smartec

Provider of innovative Fiber Optic Solutions for Structural Health Monitoring and Geotechnical Instrumentation

Logo Telemac

Provider of Geotechnical & Structural Instruments
since 1947

Logo Enomfra

Provider of Hydrogeological & Geotechnical Services. Investigations, Monitoring & Testing

Legal
  • Privacy Notice – May 2018
  • Terms and Conditions of Sales
  • Sitemap
Follow us
  • Logo linkedin
  • Logo youtube
Logo Logo